We've stumbled on this article relating to Installing A Bathtub directly below on the web and accepted it made perfect sense to write about it with you on this page.
Mounting a bathtub isn't exactly brain surgery, however it does need strong plumbing, woodworking, and also sometimes, tiling skills. Replacing an old bath tub with a new one is also a moderately tough job. If the old tub is easily easily accessible, the project can move immediately; if you have to open up a wall surface to remove the old tub and also place the brand-new bathtub, the task is a lot harder. In either instance, the job is within a home handyman's skills, although you will certainly require a helper to vacate the old tub as well as set in the new one. Ensure you have qualified yourself for the job as well as fit attempting it. Instead of working with a service provider to take over a halfway-completed task, it is much better to take into consideration using one prior to you begin. Chances are you may require an expert plumber to make tube connections.
This short article will assist you mount a new tub in your bathroom if you have actually currently acquired a new bathtub and also do not need to change the plan of your previous water pipelines.
Your tools and material checklist must consist of the following:
Preparing for the Installment
Firstly, the sustaining frame provided with the bath must be fitted (if required) according to the producer's directions. Next off, fit the faucets or mixer to the bath tub. When fitting the faucet block, it is necessary to make certain that if the faucet features a plastic washer, it is fitted between the bathroom and also the faucets. On a plastic bathroom, it is also reasonable to fit a supporting plate under the taps unit to prevent pressure on the bath tub.
Fit the versatile faucet connectors to the bottom of both faucets utilizing 2 nuts as well as olives (often provided with the tub). Fit the plug-hole outlet by smearing mastic filler round the sink electrical outlet hole, and then pass the outlet through the hole in the bathroom. Utilize the nut supplied by the maker to fit the plug-hole. Analyze the plug-hole outlet for an inlet on the side for the overflow pipe.
Next off, fit the end of the adaptable overflow pipeline to the overflow electrical outlet. After that, screw the pipe to the overflow face which must be fitted inside the bathroom. Make certain you make use of every one of the supplied washers.
Connect the catch to the bottom of the waste electrical outlet on the bathtub by winding the string of the waste outlet with silicone mastic or PTFE tape, as well as screw on the catch to the electrical outlet. Connect all-time low of the overflow tube in a similar manner.The bath need to now be ready to be suited its final placement.
Removing Old Touches
If you need to replace old taps with brand-new ones as a part of your setup, then the first thing you need to do is detach the supply of water. After doing so, activate the taps to drain pipes any water staying in the system. The procedure of eliminating the existing faucets can be fairly troublesome because of the limited access that is commonly the case.
Use a basin wrench (crowsfoot spanner) or a faucet device to reverse the nut that connects the supply pipes to the taps. Have a fabric prepared for the staying water that will come from the pipes. When the supply pipes have actually been gotten rid of, make use of the very same device to loosen the nut that holds the taps onto the bath/basin. You will certainly require to stop the solitary taps from transforming during this process. As soon as the faucets have actually been eliminated, the holes in the bath/basin will need to be cleaned of any kind of old securing substance.
Prior to moving on to fit the new faucets, contrast the pipe connections on the old taps to the new taps. If the old faucets are longer than the new faucets, then a shank adapter is needed for the new faucets to fit.
Installing the Tub
Making use of the two wooden boards under its feet, put the bathtub in the required setting. The wood boards are helpful in uniformly spreading the weight of the bath tub over the location of the boards instead of focusing all the weight onto 4 small factors.
The next objective is to guarantee that the tub is leveled all round. This can be accomplished by checking the spirit level and adjusting the feet on the bath tub up until the spirit level reviews level.
To mount taps, fit all-time low of the outermost adaptable faucet connector to the suitable supply pipeline by making a compression sign up with; after that do the very same for the various other tap.
Activate the supply of water as well as check all joints and also brand-new pipework for leaks as well as tighten them if required. Fill the bath tub as well as additionally inspect the overflow electrical outlet and the normal electrical outlet for leaks.
Finally, fix the bathroom paneling as described in the supplier's instruction manual. Tiling as well as securing around the tub needs to wait till the bath tub has been made use of at least once as this will settle it right into its last setting.
Fitting New Taps
If the tails of the brand-new faucets are plastic, then you will need a plastic port to stop damages to the string. One end of the port fits on the plastic tail of the tap and also the other end offers a connection to the existing supply pipes.
If you need to fit a monobloc, after that you will require minimizing couplers, which links the 10mm pipe of the monobloc to the standard 15mm supply pipeline.
Next off, position the tap in the mounting opening in the bath/basin making sure that the washing machines remain in location in between the faucet and also the sink. Protect the tap in position with the manufacturer offered backnut. Once the faucet is securely in place, the supply pipes can be attached to the tails of the faucets. The taps can either be attached by utilizing corrugated copper piping or with typical faucet adapters. The former kind should be linked to the tap finishes first, tightening up just by hand. The supply pipelines can later be attached to the various other end. Tighten both ends with a spanner after both ends have actually been connected.
Tiling Around the Bath tub
In the location where the bath meets the ceramic tile, it is essential to secure the accompanies a silicone rubber caulking. This is necessary as the installation can relocate sufficient to crack a stiff seal, triggering the water to pass through the wall surface in between the bathroom as well as the tiling, causing issues with dampness and feasible leaks to the ceiling listed below.
You can select from a variety of coloured sealers to blend in your components as well as fittings. They are marketed in tubes and cartridges, as well as can securing voids up to a width of 3mm (1/8 inch). If you have a larger space to fill, you can fill it with spins of drenched paper or soft rope. Keep in mind to always fill up the tub with water before sealing, to allow for the motion experienced when the bathtub remains in usage. The sealer can break relatively very early if you do not consider this motion prior to securing.
Additionally, ceramic coving or quadrant floor tiles can be made use of to edge the bath or shower tray. Plastic strips of coving, which are easy to use as well as reduce to dimension, are likewise easily available on the market. It is advisable to fit the tiles making use of waterproof or waterproof adhesive as well as grout.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
We hope you liked our post on A Step-by-Step Guide to Installing a Bathtub. Thanks so much for taking a few minutes to read through our piece. Sharing is good. One never knows, you will be doing someone a favor. I cherish reading our article about Installing A Bathtub.
Quality solution? Call.